济南精华数控设备有限公司专业从事木工雕刻机、木工开料机的研究与制造,欢迎咨询。.

栏目导航
行业新闻
公司新闻
行业新闻
联系我们
服务热线
0531-58566738
地址:山东省 济南市
木工雕刻机常见的问题解答
浏览: 发布日期:2017-11-04

  木匠雕刻机常见的四大问题处理办法

  我们都知道机械设备运用久了难免会呈现一些小问题,成都木匠雕琢机也不破例,有些原因是因为机器自身装备的问题,有些原因则是因为作业人员失误操作形成,下面科恒机械小编就为我们介绍一下成都木匠雕琢机常见的四大问题解决!

  一:木匠雕琢机作业过程中主轴电机俄然停转或转慢。

  原因:

  1、作业电压不稳或超负载,加个稳压器即可。

  2、查看中间线是否接好,线头是否有脱焊。

  二:木匠雕琢机不能在原点雕琢。

  原因:

  1、文件的版面巨细是否与机器匹配。

  2、查看是否设有偏移量(OFFSET),版面设置是否正确。

  三:木匠雕琢机发动复位时宣布反常动静或总是顶坏限位开关

  原因:

  1、顶不到限位开关,把其较正即可。

  2、驱动线触摸欠好,驱动线固定即可。

  3、限位开关线没接好,把线接好即可。

  4、限位开关损坏,换之即可。

  四:木匠雕琢机设置原点时有时向前偏移或向右偏移且偏移距离不定。

  原因:

  1、限位开关失灵,在体系回到体系原点的过程中限位开关已闭合又弹开。换限位开关即可。

  2、驱动线松动。设法把其固定紧即可。

  The carpenter carved machine four common approach

  We all know that the use of mechanical equipment for a long time will inevitably have some small problems, Chengdu carpenter engraving machine is no exception, some reason is because the machine the equipment, some of the reason is because the operating personnel misoperation formation following Keheng machine small for four problems we introduce Chengdu carpenter carving machine the solution!

  A carpenter: engraving machine in the process of the spindle motor suddenly stopped or slowed down.

  Reason:

  1, the operating voltage instability or overload, plus a regulator can.

  2, check the middle line is connected, whether there is a connecting thread.

  Two: carpenter carving machine can not be carved at the origin.

  Reason:

  Whether 1, file size, layout and machine.

  2, check with offset (OFFSET), the layout is correct.

  Three: carpenter carve machine launched reset or abnormal movement announced always top the bad limit switch

  Reason:

  1, not to the limit switch, it is.

  2, drive line touch is not good, the drive line can be fixed.

  3, the limit switch line not connected, connect the wire.

  4, limit switch damage, change it.

  Four: carpenter carve machine set the origin sometimes forward offset or offset to the right and offset distance is not fixed.

  Reason:

  1, limit switch failure, a switch has been closed and opened the process of the origin of the system to the system. Switch the limit switch.

  2, drive line loose. Try to fix it tight.